Advantek Networks (USB 2.0) Manuel d'utilisateur

1 USB Wireless LAN Adapter User’s Manual Model # AWN-USB-54S

10 STEP8: When the adapter is installed properly, the configuration utility will be displayed automatically. STEP9: After the setup

11 To check if the adapter is properly installed, you can right-click My Computer  choose Properties  click Device Manager. The Configuration

12 2.2 Install Driver for Vista Step 1: Once USB Wireless LAN Card is plugged into the Computer, you will see the Found New Hardware windows is show

13 Step 3: Please wait for a while during the USB Wireless LAN Card is configuring your new software installation. Step 4: After setup has fi

14 To check if the adapter is properly installed, you can right-click My Computer  choose Properties  click Device Manager.

15 3. Wireless Network Configuration Utility The Configuration Utility is a powerful application that helps you to configure the Wireles

16 STEP3: Uncheck “Use Windows to configure my wireless network settings” to enable the utility for the adapter and then click OK to continue. Note:

17 3.2 Link Status In this section, you can immediately monitor the current connected link status, such as Link Speed, Throughput, Link Quality, S

18 Status: Display the SSID and MAC ID of the network that the adapter is connecting to. Extra Info: Display the link status. Channel: Display the nu

19 make connection.  If the intended network has encryption other than “ Not Use ”, RaConfig will bring up the security page and let use input the

2 FCC Warning This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC

20 Profile Name: Define a recognizable profile name for you to identify the different network. SSID: The SSID (up to 32 printable ASCII characters)

21 stations. If there are only 802.11b wireless stations in the network, you can set the card to this mode. 802.11 B/G mix – If you have a mix of

22 3.3.2 Authentication and Security Authentication Type: This setting has to be consistent with the wireless networks that the adapter i

23 WPA2 – Like WPA, WPA2 supports IEEE 802.1x/EAP authentication or PSK technology. It also includes a new advanced encryption mechanism using the Ad

24 Fill the text box by following the rule below: 64-bit – Input 10-digit Hex values (in the “A-F”, “a-f, and “0-9” range) or 5-digit

25 Authentication Type: The EAP authentication protocols this adapter has supported are included as follows. This setting has to be consis

26 Identity: Enter the name as the identity for the server. Password: Enter the password as the identity for the server. Use Client Certificate: A cl

27 Allow Intermediate Certificates: A server designates an issuer as a trusted root authority by placing the issuer’s self-signed certificate, w

28 or more reties. 4. Frames Fail To Receive ACK After All Retries: Frames failed transmit after hitting retry limit. 5. RTS Frames Successfull

29 802.11 B only – This adapter can be compatible with both 802.11g and 802.11b wireless stations. If there are only 802.11b wireless stations

3 Revision History Revision History V1.1

30 applied to the multimedia application or a voice call. The adapter will fast roaming to the near network when the receive sensitivity (signal stre

31 3.6 QoS The QoS Page of RaConfig. It involves “WMM Enable”, “WMM – Power Save Enable” and DLS setup. WMM Enable: Enable Wi-Fi Multi-Media. W

32 Step3: Change to “Site Survey Page”. And add an AP that supports WMM features to a Profile. The result will look like the below f

33 3.6.2 Enable WMM – Power Save Step1: Click “WMM – Power Save Enable”. And Click “Setting…” button. Step2: After clicking “Setting…” butto

34 3.6.3 Enable DLS (Direct Link Setup) Step1: Click “Direct Link Setup Enable”. And Click “Apply” button Step2: Change to “Site Survey Page”. A

35 The Setting of DLS indicates as follow: 1. Fill in the blanks of Direct Link with MAC Address of STA. The STA must conform to two conditions as f

36 3. Click “Apply” button. The result will look like the below figure. Describe “DLS Status” as follow: 1. As the up figure, after configuring D

37 Step2: Double click. And the result will look like the below figure. 3. Disconnect Direct Link Setup as follow: Step1: Select a direct link STA

38 Step2: Click “Tear Down” button. The result will look like the below figure. 3.7 About About page display the wireless card and driver version

39 In the “About”, you can click the hyperlink to connect the website for the information of the wireless chipset vendor and review basic inf

4 Contents 1. Introduction...5 1.1 Features ...

40 4. Troubleshooting This chapter provides solutions to problems usually encountered during the installation and operation of the adapte

41 Possible Remedy: Move the antennas of the access point or wireless router into an L shape (one vertically, and one horizontally). Click on th

42 10. What does IEEE 802.11 feature support? The product supports the following IEEE 802.11 functions: -- CSMA/CA Plus Acknowledge Protocol -- M

43 software than previous encryption standards. It is also included in IEEE 802.11i standard. Compare with AES, TKIP is a temporary protocol

5 1. Introduction This adapter is an IEEE 802.11g client device that delivers unrivaled wireless performance for your desktop PC or lapto

6 2. Installation Procedure Note: If you have installed the Wireless USB 2.0 Adapter driver & utility before, please uninstall the old version

7 STEP2: Insert Installation CD into CD-ROM drive then windows below will appear. Click Install Driver to begin device driver installatio

8 STEP4: Please read the following license agreement. Use the scroll bar to view the rest of this agreement. Click Yes to accept the agreement. STE

9 STEP6: If you need the adapter to operate with better performance, please choose Optimize for performance mode to enable the Tx Burst mode. Or you